*ONLINE CHAIR CANING & SEAT WEAVERS UNIVERSITY TM HOW TO E

A LOST ART FOUND SM!!!

          Having A Museum Quality Chair
                     By Ronnie P. Goff
                Copyright April 13, 2006

Machine Cane Chair Preperation 101!!!
Machine Cane Wedges!!!

Machine Cane Wedges absolutely must have the sharp edges
removed before using them on a Machine Cane Chair Bottom!!!

Machine Cane Groove Preperation 101!!!

* The sharp edges on the absolute very top of the inner groove
must be removed without damaging the Machine Cane Groove prior

to your installing the machine cane!!!
This must be done very precisely!!!
The tool you use for removing the sharp edges is a radius plane!!!

COUNTRY SEAT WEAVERS' TM
THE CANE SOAKER TM IT
COMPLETELY SOAKS YOUR
MACHINE CANE BECAUSE IT
SOAKS IT IN 360 DEGREES OF
WATER!!! WE SOAK 4 24 HRS.
WITH NO EXCEPTIONS!!!

COUNTRY SEAT WEAVERS TM
3RD HAND!!! MAKES HAND-
LING 7' OF MACHINE CANE A
1 MAN (WOMAN) JOB!!!

PUTTY KNIFE CHISEL
USED IN SPLINE RE-
MOVAL!!! THEN WE USE
SPLINE REMOVAL
CHISELS!!! NO TEAR
OUTS!!!

FRAMING SQUARE 4 LAY-
ING OUT CHAIRS' / SOFAS'
!!! LAY OUT FRONT / BACK
SAME TIME MEASURE ONCE
!!!

* We also use WD - 40 along with a Number 1, & A number 3
Spline Chisel for removng the Machine Cane from a Machine Cane
Bottom Chair!!! Why W - D 40, & for what? It's magic!!!

FRAMING SQUARE FOR
LAYING OUT CHAIRS' /
SOFAS'!!! LAYING OUT
SIDES PERFECTLY SQ.!!!
USE LAYOUT LINES/
"WITNESS MARKS"
FRONT/BACK/SIDES
DEAD CENTER!!!

MACHINE CANE WEDGES
POSITIONED AT LAYOUT
LINES/"WITNESS MARKS"!!!
  SO MACHINE CANE IS
100% "SQUARE!!!"



MACHINE CANE WEDGE TO
INSTALL MACHINE CANE!!!
DRIVE THE MACHINE CANE
GENTLY TO BOTTOM OF
GROOVE!!!

APPLY WHITE GLUE IN
GROOVE BEFORE IN-
STALLING SPLINE!!!

* Using a modified Carpenter's Framing Square (the blade or
body is shortened to 6" so you can do all sizes of Machine Cane
Chairs' & Sofas') to layout odd shaped Machine Cane Chair Bottoms
makes it extremely accurate, & much easier to do your Machine
Cane Chair bottom layouts accurately!!!
Measuring once, laying out front, & back at the same time, &
saving additional time in the lauout process!!!

MACHINE CANE B 4
FINAL TRIM!!! LEAVE
270 DEGREES OF
MACHINE CANE AFTER
TRIM!!!

TRIM FLUSH 2 MACHINE
CANE SEAT BOTTOM
FRAME!!! SPLINE FLUSH
2 MACHINE CANE SEAT
BOTTOM FRAME!!!

DATED CIRCA FEBRUARY
18, 1896 OFFICE CHAIR
USED 113 YRS. AGO BY
WHOM, & FOR WHAT
PROFESSION?

MACHINE CANE JIG BOX TM
COPYRIGHT 2006 - 2009

MACHINE CANE JIG BOX TM
DIMENSIONS AS FOLLOWS:
24' TALL X 10 - 1/2" WIDE
X 6" DEEP
9" INSIDE TO INSIDE
USE 2" X 6"S & 1" X 6'S
COPYRIGHT 2006 - 2009

MACHINE CANE JIG BOX TM
IN USE!!!
CHAIR CAN BE MOVED FROM
AREA TO AREA DURING
MACHINE CAN INSTALLATION!!!

* The reason for The Machine Cane Jig Box TM is "FORCE...
At the same time surface force resist the downward force with
equal upward force!!!"

          When you install Machine Cane in the bottom of a Machine
Cane Chair you are very gently applying downward FORCE!!!
          When you install the Spline in the Machine Cane Chair Bottom
to hold the Machine Cane in place you are applying much more
downward FORCE!!!
          You can now completely eliminate downward FORCE when
doing a Machine Cane Chair Bottom by using a Machine Cane Jig
Box TM!!!
          It almost completely eliminates breaking, splitting the Machine
Cane Chair Groove area, etc. when doing a Machine Cane Chair Bottom!!!
          "Since antiquity, scientist have used the concept of FORCE in
study of stationary, and moving objects!!!"